In radio engineering and telecommunications, standing wave ratio is a measure of impedance matching of loads to the characteristic impedance of a transmission line or waveguide. Impedance mismatches result in standing waves along the transmission line, and SWR is defined as the ratio of the partial standing wave's amplitude at an antinode to the amplitude at a node along the line. The SWR is usually thought of in terms of the maximum and minimum AC voltages along the transmission line, thus called the voltage standing wave ratio or VSWR. For example, the VSWR value 1.2:1 denotes an AC voltage due to standing waves along the transmission line reaching a peak value 1.2 times that of the minimum AC voltage along that line. The SWR can as well be defined as the ratio of the maximum amplitude to minimum amplitude of the transmission line's currents, electric field strength, or the magnetic field strength. Neglecting transmission line loss, these ratios are identical. The power standing wave ratio is defined as the square of the VSWR, however this terminology has no physical relation to actual powers involved in transmission.
The standing wave ratio meter, SWR meter, ISWR meter, or VSWR meter measures the standing wave ratio in a transmission line. The meter indirectly measures the degree of mismatch between a transmission line and its load.
The Standing wave ratio determines how good your reception and transmission will be. A perfect ratio is 1:1, the maximum acceptable ratio in CB is usually 2:1. If you listen to a 1:1 aligned radio system and a 2:1 or more you will hear an obvious difference in quality. It’s important to keep your radio system aligned not only for the quality though, a bad ratio can hurt your radio device in the long-term, sending it to an early retirement if you don’t take care of it.
Move your vehicle to open ground. If you have instructions that came with your specific meter device follow them. Try not to have any physical barriers such as walls or trees around you. If the ratio isn’t good, try changing your setup. Sometimes you will need to change the length of the antenna, try to do it in ⅛ increments. Try to move your antenna around, make sure it’s grounded well. This is the most important part of your configuration, determining the final position of your antenna and cables. Try not drilling anything in before you do this.In short, a meter is required to:
Many ham radios already have built in SWR/Power meters along with other features. Consider your setup:
The SWR Meters for VHF tends to be a more advanced device, with power meters feature, different sensors and connectivity. These are intended mostly for base stations in ham radio configurations and come with a price. You cannot compare them to the minimal needs of CB radios who are on the HF band.
Consider small SWR meters for Standing wave Ratio. You can also connect that device to your lighter plug or to the fuse-box. Permanent In-line meters would be the easiest to install, if you compare them to equipment you only connect temporarily for check-ups
For ham radio there are many different configurations and testing equipment, usually they also include built-in power meters to measure transmissions. if you’re not sure what device to get for your configuration. Try to compare the features these products have, call us or send us a message and we’ll help you choose the best product for your setup.
"Is My Antenna System OK?" Stop Guessing with this SWR Test Kit. Includes meter, 3ft jumper cable and measuring SWR book. Complete SWR package includes a compact SWR meter, a short 3 foot coax cable to connect the meter to your CB and an SWR booklet from Firestik
Test Your Radio WITHOUT Testing The Neighbors! Transmit into this dummy load instead of your antenna for accurate wattage measurements.
Easily measure Power, Modulation, & SWR and Transmit Frequency! Add this beautiful multi function meter to your shack! The Dosy TFB-3001-S multi function meter is designed to work on CB and the ham radio HF bands to display transmitted frequency as well as output Power and Modulation.
Didn't Get a Frequency Counter In Your Radio? - Easily added to your radio with a simple plug in - On radios equipped with a jack on the back. Universal frequency counter which indicates the frequency of the selected channel. It is designed for use in CB and amateur radios.
Will This Work? - Try This Simple Test! While hearing the noise you want to filter, unscrew and unplug the coax antenna cable from the back of your radio (don't transmit!). If the noise is still there, the filter should work. If is goes away, you are receiving noise as a signal. Power line filter product used to remove unwanted RF (engine noise, inverter noise, other electronic interference) from your CB radio or stereo.
The OPEK SWR6L is a compact SWR and Power meter product designed for operation in the HF band, including CB Radios. The LED illuminated display makes for convenient night-time usage. Accurate within 5%.
Compact SWR and Power meter with a large, cross-needle display for CB and 10 meter radio frequencies. *note this meter does not light up, regardless of the part number."
Super compact, easy to use SWR and power meter installs quickly in-line between your radio and antenna. This is NOT a CB meter. UHF/VHF only.
Super compact, easy to use meter Model PDC-1 test instrument is a compact 3-function test meter product designed to indicate the condition of any 52 ohm antenna and antenna coax used for CB radio operation by testing for Standing Wave Ratio (SWR)
The PDC2 SWR Meters / test instrument is a compact 3-function test meter product designed to indicate the condition of any 52 ohm antenna and antenna coax used for CB radio operation.
Will This Work? - Try This Simple Test! While hearing the noise you want to filter, unscrew and unplug the coax antenna cable from the back of your radio (don't transmit!). If the noise is still there, the filter should work. If is goes away, you are receiving noise as a signal. This device lets you filter out unwanted RF interference, static, or noise with this power line filter. Rated up to 20A this filter will work with radios that output up to 100 watts PeP.
The FC30 frequency counters are easy to use, easy to see, and easy to mount devices. The 6 digit display is bigger than most displays we've seen, making it easy to read from a distance. Comes with a dim button on the front to tone down the LED lights
RED These FC30 frequency counters are easy to use, easy to see, and easy to mount devices. Comes with a dim button on the front to tone down the LED lights
Diamond antenna SX400 meter for 140-525 MHz bands. The SX-400 is an insertion type SWR / Power meter being connected between a transmitter and an antenna. 12VDC power required for operation. Power cord included.
Super compact, easy to use power and SWR meter, installs quickly in-line between your radio and antenna. No calibration need for the meter function. Small in size SWR and Power Meter with low insertion loss allows it to be permanently connected.